INT: COMPLETE LED DASH - including all switches

[YOanthony]

I cant see any of the pics for what this looks like?

Neither, all of the links have www.**** and it's not coming up. Can the poster or admin fix this?

[megarock15]

Hey mike post of off topic but if i do the tail light, corner, and bumper light led conversion would i need load ballencers for each light? And also what should i use to make them?

[809king]

neither, All Of The Links Have www.**** And It's Not Coming Up. Can The Poster Or Admin Fix This?

X2

[91cblx]

This thread is 7 years old, i just went to the site where he got his led bulbs from, and they are no longer selling anything I would also like to know of a new link though?

[HenRoc]

SuperBrightLeds.com

[Hondapawa]

Very nice diy!

I'm just wondering about the trunk lighting and the door courtesy lights.

I looked on super bright leds and they sell those type of leds:

http://www.superbrightleds.com/cgi-b....27551&next=50

3022-x4 LED Festoon bulb
30x10mm (1.181 inches long)12 VDC Festoon Base Bulb with 4 LEDS

Would that led work to replace the stock trunk bulb?Will it fit in the socket? And is the 4 led version bright enough?

[crx08]

What type of relay do you use for the turn signals when converting the front and rear turn signals to LED's??

I was looking at the electronic LED flasher relays 3/4 the way down the page
http://www.superbrightleds.com/cgi-b...rake-turn.html

[WhiteShift]

i have make mine without the #194 socket, i have used leds with resistor and i have solder them directly on the board..... the inside result of the cluster look a lot home made but when reassembled the result look really nice. i have used about 12 led and this only on the cluster.

this is easy way to make it as i think,
i have verify all my solder 2 time,
and hope they will hold on place.
this is the result i got.

[illinois_erik]

[/QUOTE]

Thats Fawesome! Ill eventually get around to doing this but mix in some Ultraviolet LEDs too

[STL_92_Accord]

This diy is a must imho. And the fact that superbright led is literally in my backyard less than five mins from my house i would be a fool not to do it

[cp[mike]]

i have make mine without the #194 socket, i have used leds with resistor and i have solder them directly on the board..... the inside result of the cluster look a lot home made but when reassembled the result look really nice. i have used about 12 led and this only on the cluster.

this is easy way to make it as i think,
i have verify all my solder 2 time,
and hope they will hold on place.
this is the result i got.

love it, thanks for keeping up this awesome mod. i commend you doing it the cheap hardcore way, with component LEDs. any pics of the work along the way?

and yes i need to update the link but SUPERBRIGHTLEDS.COM is awesome now

[WhiteShift]

love it, thanks for keeping up this awesome mod. i commend you doing it the cheap hardcore way, with component LEDs. any pics of the work along the way?

and yes i need to update the link but SUPERBRIGHTLEDS.COM is awesome now

here is few picture.. only for the climate control. i dont have picture for the dashboard.

enjoy.

[Jarrett]

That light output is very focused. You need to sand those bulbs at the very least. It would be best if you could rig some type of diffuser in there to spread the light better though.

[SuddenCb7]

I know this is very old post but a very good write up.. I'll be doing this soon. Really I just needed the resistor code cause i was to lazy to do the math.. Thanks mike.