quaidum : 1993 Accord EX

[quaidum]

Mods List:

ENGINE:BOTTOM END
f22a6 block
85.5mm cast piston w/coating on crowns and skirts(soon to be bisimoto forged internals 9.1 CR pistons w/longer length rod)
kaizenspeed balance shaft eliminator
new oil pump
acl bearings
esp solid motor mounts
f22a4 header

HEAD:
bisimoto level 1.2 turbo regrind camshaft
bisimoto pro springs
bisimoto non-slip cam gear
bisimoto heat shielding intake gasket
mild port and polish job(mostly on the exhaust ports)
h23 intake manifold w/iab spacer and egr removed
new oem retainers
new oem valve stem seals
arp head studs

SUSPENSION:
koni yellow SP3 version with ground control koni yellow sport perches
ground control custom coil-over sleeves 500lb F 400lb R
esp 3 point and 4 point strut bar
energy suspension master kit
TAS adjustable upper control arms
new oem wheel bearings
new oem lower ball joints
new oem inner and outer tie rods

FUEL:
aem fuel rail(i know not necessary, but got it cheap and it looks good)
walbro 255hp
stock injectors(550cc injectors for the turbo)

BRAKES:
cb9 EBC slotted and dimpled 11.1'' rotors 25mm thick
cb9 calipers
cb9 25t brackets
EBC RedStuff pads
earls SS lines all around

EXTERIOR:
morimoto mini d2s bi-xenon 4300k e-46r shrouds retrofitted into 90-91 JDM one-piece headlights
black bumper lights
aftermarket fog lamps

INTERIOR:
removed everything beside dash, center console and driver door panel

WEIGHT REDUCTION:
ac delete
balance shaft delete
retrofitted lights
interior gutted
Corbeau Forza racing seats


AUDIO/ELECTRONICS: NONE

FUTURE PLANS:
install garrett 58 trim .48 turbine .60 comp.(purchased)
bisimoto 9.1 CR piston w/coating and longer rods(purchased)
ebc slotted & dimpled 11.1'' rotors(purchased)
ebc red stuff pads(purchased)
some front end goodies(lip, fogs, and such)
5 lug swap with gunmetal tl type-s 17X8(looks similar to zo6 rims)
repaint

[slick]

get bigger pics or try to resize them when you go back to the library

[91ExSedan]

Looks nice from what I can see.
But, try to resize them, as Slick said.

[quaidum]

ok i fixed the size problem and added more info

[kouzie]

so far so good........

[slick]

now you need to redo your first post. your supposed to put one pick then a mod list and then the rest of your pics. makes for less confusion when trying to figure out what all you got.

and the turbo stuff looks good

[JoshM]

Nice rear strut bar!

[quaidum]

well i got some h.i.d's put in the car they are 6000k the order of the pics are parking lights, parking + fog, then those + low beams, then inside.












i'll try to get some more pictures and maybe a video or two

[PointBlank]

Love the rimsNot a fan of the headlights though..Nice turbo setup.

[19TcappaLX]

cb got alot of potential,good start you got there.

[excalibur02]

some nice parts you got installed and waiting to be installed!

[quaidum]

new turbo

here is my new turbo on the right its a garret gt journal bearing 0.60 compressor and 0.48 turbine 58 trim wheel next to a big 16g



the engine is starting to be built this monday so the i am about to start taking mine out will have plenty of pics of the project and build

[PointBlank]

here is my new turbo on the right for $120 its a 20g next to a big 16g

Looks like a monster..

[quaidum]

just received my solid mounts yesterday from ESP it took them forever this time. i paid for them on 4-13-09 and didn't get them until 6-4-09 the wait sucked but they are here now i will get some pics soon hopefully.
monday i finished putting in my kaizenspeed balance shaft eliminator kit went fairly smoothely. just picked up the crank from the machine shop and am about to start putting the bottom end together wil get some pictures of that as well

[quaidum]

just bought bisi 1.2 turbo cam, cam gear, heat shielding intake gasket,and pro springs set me back $571.00 and $54.55 shipping prioriety mail going to pick up my ported head right now will get pics