O2 sensor replacement !

[dbsharp]

im getting about 30 mpg mixed city and highway. thats with me getting on it a lot too. proper maintenance and a/f ratio make a difference.

[Accord07]

new from honda or aftermarket?

if it's aftermarket, i give it a week or a month before it fails.

Its OEM, I did get it online however for $60. I got a denso one versus the NGK one. They both practically come out to be the same.

[ACCORDEX92]

Its OEM, I did get it online however for $60. I got a denso one versus the NGK one. They both practically come out to be the same.

Which site is that cause I need one too

[bcjammerx]

the bosch works fine and is around 50

[lucid]

Did mine today...thanks for the motorvation.
Hope my taillight doesn't turn black from exhaust again.

[prNonVtec4u]

more POWA' from an 02 sensor...???...

ima get me some! lol

[semitas]

just ordered and ngk for my integra, i did spark plugs, wires, dist. cap and rotor, fuel filter, lucas fuel injector cleaner and im still getting 200miles per tank, thats not what your supposed to get from a 1.8, so the only thing left is the o2 sensor, i think it might be the original one in there right now, i did pick up a few more after putting in the short ram intake

[93SM4_CB7]

where can i order a NGK o2 sensor and does the cb7s have a front and back ? im looking to replace them and is there a DYI for this .. seems like a simple unscrew/screw splice together ..key word "seems" ..lol


thanks

[phantomcow2]

where can i order a NGK o2 sensor and does the cb7s have a front and back ? im looking to replace them and is there a DYI for this .. seems like a simple unscrew/screw splice together ..key word "seems" ..lol


thanks

The CB7 has just one O2 sensor. It is located on the exhaust manifold underneath the heat shield. Replacement is so simple that it may not even need a DIY: unscrew the old sensor (22mm wrench), screw in new one. It'll just clip right into the factory harness, no splicing necessary.
The O2 sensor is located behind the catalytic converter if you've got the F22a6 engine (EX or SE model).

[93SM4_CB7]

The CB7 has just one O2 sensor. It is located on the exhaust manifold underneath the heat shield. Replacement is so simple that it may not even need a DIY: unscrew the old sensor (22mm wrench), screw in new one. It'll just clip right into the factory harness, no splicing necessary.
The O2 sensor is located behind the catalytic converter if you've got the F22a6 engine (EX or SE model).

thanks ..

[ja23merz]

there are 2 locations for the O2 sensor depending on what engine you have. f22a1's sensor is on the header and the f22a4/f22a6 is right before the cat converter on the downpipe. make sure you buy the right one for your motor, or else youre going to have to splice some wires, because the plugs are different between the f22a1 and the a4/a6

[ACCORDEX92]

So what o2 sensor do I have to buy 92 f22a6 or 95 h22a

[bcjammerx]

So what o2 sensor do I have to buy 92 f22a6 or 95 h22a

whatever engine is in your car...the o2 sensor for that

[TheNextAZN]

quick question, would h22 guys have to buy a o2 sensor for the h22a/a1/aX, or a o2 sensor for their previous f22a1/a4/a6 ?

[bcjammerx]

quick question, would h22 guys have to buy a o2 sensor for the h22a/a1/aX, or a o2 sensor for their previous f22a1/a4/a6 ?

I already answered your question...

You would use whatever o2 sensor goes with your engine.

I will not put an o2 sensor for an 84 celica/supra's engine in my 84 celica/supra that is powered by a 94 1uz-fe...same with your honda engines...doesn't matter the car body...but the engine