Announcement

Collapse
No announcement yet.

H22 swap questions, vacs, plugs...*ASAP*

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

    H22 swap questions, vacs, plugs...*ASAP*

    Hi,

    I had a few questions when I'm going back to plugging everything from the F22's harness into the H22.

    I have pics.

    This is a pic of my F22 harness on my H22...I can't seem to figure out which plug this is, the one circled in red. Any Ideas? This plug is located below the TB on the passanger side of the car near the main harness plugs back to the car.

    This is my drivers side TB on the H22. What do I plug into these two vacs that I have circled here?

    This is my black box above the charcol canister, where do I plug this vac line in?

    Thanks a lot.
    Attached Files
    2DAO (2 Door Accord Owner)
    JDM H22 DOHC 200/161 2.2L
    My members ride: http://www.cb7tuner.com/vbb/showthread.php?t=20385

    #2
    *BUMP* please. This is my only car and I still can't figure out what that plug is, nor how to connect the two vacs on driverside of the TB.

    Thanks
    2DAO (2 Door Accord Owner)
    JDM H22 DOHC 200/161 2.2L
    My members ride: http://www.cb7tuner.com/vbb/showthread.php?t=20385

    Comment


      #3
      worry about that when the engine is in.. seriously.. dont try to figure it out now.. u have other things to worry about .. like getting it in. once thats done then worry about this.. vac lines are easy.. this is one reason why i have always said to LABEL EVERYTHING BEFORE U REMOVE IT AS BEST AS POSSIBLE!! but noooo no one listens..


      Praise The Lowered...

      Comment


        #4
        The hoses on the drivers side.. I plugged the top on, bottom one should go to the line that is on the drivers side fender well. At the end of that, it splits into two, i plugged the one that goes to somewhere.. left the one alone that goes into the fender.

        The hose out of the black box will go to the EGR.

        The plug looks like it could be for the EGR... if you use the accord egr, use accord plug, prelude egr, prelude plug.

        Comment


          #5
          ok, it's not the EGR...the only quesion I have left at the moment, the motor is in, is what that plug goes to.

          I just hope that SOB is wired correctly =D
          2DAO (2 Door Accord Owner)
          JDM H22 DOHC 200/161 2.2L
          My members ride: http://www.cb7tuner.com/vbb/showthread.php?t=20385

          Comment


            #6
            Originally posted by TheTempest
            ok, it's not the EGR...the only quesion I have left at the moment, the motor is in, is what that plug goes to.

            I just hope that SOB is wired correctly =D
            i hope so too
            is that plug for the VSS(vehicle speed sensor)???
            5.6L V8 32V DOHC
            JDM HERITAGE - US BUILT

            Comment


              #7
              looks like an 02 sensor connector.
              H22 Prelude VTEC 92-96 200 161 10.6:1 87 90 DOHC VTEC 2157 JDM

              190.3whp 155 wtq - with bolt ons, and a dc header

              ET=14.457 @ 94mph w/ 2.173 60Fter

              Comment


                #8
                not the spedo, nor the O2
                2DAO (2 Door Accord Owner)
                JDM H22 DOHC 200/161 2.2L
                My members ride: http://www.cb7tuner.com/vbb/showthread.php?t=20385

                Comment


                  #9
                  the plugs wires are Blue/Grn and Blue/Yel if that helps.
                  2DAO (2 Door Accord Owner)
                  JDM H22 DOHC 200/161 2.2L
                  My members ride: http://www.cb7tuner.com/vbb/showthread.php?t=20385

                  Comment


                    #10
                    Maybe its a plug in for the auto tranny??
                    H22 Prelude VTEC 92-96 200 161 10.6:1 87 90 DOHC VTEC 2157 JDM

                    190.3whp 155 wtq - with bolt ons, and a dc header

                    ET=14.457 @ 94mph w/ 2.173 60Fter

                    Comment


                      #11
                      Scrolling back thru my mental pictures of my install. That plug went to a connector on the back of my auto tranny. It's the only plug back there. I'm at work and I dont have my manual w/ me otherwise i'd give u the name of it. I'll post it when i get home in an hour.

                      mmmmmmmmmmmmmm....... DOHC

                      Comment


                        #12
                        Told ya leave it out! its not gona do shit.
                        H22 Prelude VTEC 92-96 200 161 10.6:1 87 90 DOHC VTEC 2157 JDM

                        190.3whp 155 wtq - with bolt ons, and a dc header

                        ET=14.457 @ 94mph w/ 2.173 60Fter

                        Comment


                          #13
                          lol.

                          Thanks guys, that really makes me feel a lot better. =D

                          Tomorow should be the big day, I have to get some belts for the PS/Alt/AirComp and then I'm going to try to start that bad boy =D
                          2DAO (2 Door Accord Owner)
                          JDM H22 DOHC 200/161 2.2L
                          My members ride: http://www.cb7tuner.com/vbb/showthread.php?t=20385

                          Comment

                          Working...
                          X