just bought 1 pice headlights.

[iwork4mycb7]

hey guys i juss bought 1 pice headlights on ebay they look in pretty good condition they were 270 shipping 30, but my question is, r they gonna fit my 92 dx perfectly? or im gonn have 2 do modifications? how about for the lighting? were can i buy the jdm bulbs?

[JoshM]

r they gonna fit my 92 dx perfectly? ?

They bolt on.

or im gonn have 2 do modifications

Trim the bottom bracket a tiny bit. You'll see what need to be trimmed when you try to put on the lights.

how about for the lighting?

What about the lighting? They have bulbs that light up, just like USDM lights.

were can i buy the jdm bulbs?

Why do you need JDM bulbs? USDM bulbs will work. H4 = lows, H1 = highs.

[jhoff]

wait did you buy them off ebay?
http://cgi.ebay.ca/ws/eBayISAPI.dll?...m=220366863122

because if thats you then should bolt right up

[iwork4mycb7]

^^^ yeah i bought those.... lol

[iwork4mycb7]

oh and thanks josh for the quick reply...

[JoshM]

oh and thanks josh for the quick reply...

[ikayto]

wait did you buy them off ebay?
http://cgi.ebay.ca/ws/eBayISAPI.dll?...m=220366863122

because if thats you then should bolt right up

partially correct, they will bolt up but the brackets still look intact. he will still need to cut them, otherwise the bumper will not slide in fully.

[g7kobayashi]

are they official stanley made ones?
no cutting work needs to be done in my experience
if they're real jdms, neither the 1-piece nor 2-piece.

[JoshM]

when i installed my 9091's, the bumper wouldnt fully sit against the car until i cut part of the mounting bracket off, seen in the pic below. i cut along the red dotted line (dont mind the red circle). i guess i should have used a dremel, but it wasnt outside with me, and i had a pair of wirecutters in my hands from when i did wiring... so i cut the plastic w/ them compare the brackets from the jdm headlights to ur stock ones when they finally arrive, and see if you do in fact need to make the cut.
[IMG]http://www.****.com/pics/jdmheads/cut.jpg[/IMG]

.

[kouzie]

wait did you buy them off ebay?
http://cgi.ebay.ca/ws/eBayISAPI.dll?...m=220366863122

because if thats you then should bolt right up

Those are very nice......
They'll fit perfect...

[ikayto]

are they official stanley made ones?
no cutting work needs to be done in my experience
if they're real jdms, neither the 1-piece nor 2-piece.

well looking at your sig, you had a jdm bumper with a jdm support, so of course it would fit with no cutting lol.

us bumper support is different than jdm, it hits the bracket on the jdm headlights if you leave them uncut.

[JDMCB3Si]

I NEVER had to cut any parts of my JDM 1 pieces to fit. and everything bolted up and looked OEM

[Smiley_cb7]

Yea, you gotta do some cutting but nothing major though. Its not like your hackin stuff all up. Very minor, or at least I had to on mine.GL

[g7kobayashi]

well looking at your sig, you had a jdm bumper with a jdm support, so of course it would fit with no cutting lol.

us bumper support is different than jdm, it hits the bracket on the jdm headlights if you leave them uncut.

i used to have either 1-piece or 2-piece with stock bumper.
the bumper support is still stock and i even took off the styrofoam
because the curve of front edge is different.
i just checked some pix i took before and i have to say that
i was wrong. someone made the cutting before i installed it.

[ikayto]

i was wrong. someone made the cutting before i installed it.

figured that's the reason why everyone who has said they didnt have to cut anything, it's because they were precut :]