Slid and Hit the Curve = BIG DAMAGE

[AbsurdNY]

I've taken that entrance many times, That small curb did that much damage? Did you run over all the pot holes on the entrance also?

X2. Most of the onramps on the belt are all messed up.

[XcluziveAZN]

You had to have been going faster than that...

I smacked a curb multiple times in my cb and never did anything that bad. Sucks though.

I'd be weary of inner tie rod, cross member front and rear.

I hit it from the side. If i hit it straight on my wheel would of jump it but since the car was side way. It hit pretty hard from the side that is why my rim cracked

Time to hunt for parts and $$$

LIRR for the next 4-6 weeks

Edit: I just bunch of knuckle on ebay for Dirt Cheap! I wonder if locally will be the same

Edit: I have to get one with ABS right? Since my car is 93 accord 2dr EX and I know i have ABS

[Pazzword JDM]

rockauto.com has good quality parts for cheap, check em out. or hit up ye old junk yard.

[vietkid_2006]

sliding at a curb side ways causes more damage then just head on...

i know that for a fact..

[XcluziveAZN]

Updated:


Took everything apart

Knuckle is not bent so yay!! Axle is fine and no play yay? But Axle nut doesn't come off after Electric Impact, Breaker bar and Torch it......Booo soooo i took off the whole thing!! Knuckle and Axle in one piece...Will have to carry to local shop and have them take it off some how

here the pic...something is wrong in one of the pic but not sure if it is wrong...the picture with the sway bar...can that cause positive camber?









Any input?

Thank You for a lot of helpful advice so far

[bobbycos]

because i'm guessing i have to replace other side too since i'm replacing one side


anyone Know any good Junkyard in NYC ?

i have the set of knuckles already out of a car and ready to be rebuilt if you need. i know for a fact that the bearings in 'em are shot but i would put new ones in anyways. PM me


before i forget i have a set of good used calipers too with the mounting brackets

[Bullhorn7]

How hard did you hit!!??? I hit a curb going 30 and bent 2 rims... Nothing more

[JunyAccord]

Lol you sound like me when i was doing a makeover with my front susp. I couldnt get the axle nut off. 2 broken ratchets later i took it to a small shop (1000 ft/lb impact gun) and no success. Then i took it to a tranny shop (2000 ft/lb impact gun) and it came out like butter. Didnt charge me nothing.

you will probably need new sway bar links. Mine is kinda bent up but it didnt effect my alignment

[XcluziveAZN]

How hard did you hit!!??? I hit a curb going 30 and bent 2 rims... Nothing more

Can i say hard? I don't remember how fast i was going, I was coming down straight catching the light and did not slow down fast enough for sure.

I feel like going back and re read that story of turtle and rabbit race ....... how turtle win at the end....I'm guessing i'm a rabbit right now


Does Lower Control Arm look Bent in the picture?



Does not look like that

[jimy]

There was a guy on here selling a complete 5 lug conversion with the rims for $600-700. I would of gone that route.

[gloryaccordy]

You can get a whole knuckle with all that shit for like $100 shipped

[XcluziveAZN]

You can get a whole knuckle with all that shit for like $100 shipped

my knuckle is fine. i updated the post

[gloryaccordy]

Lookin at ur sway bar link

Looks like u might need a new front crossmember. The radius arm (arm that goes from front crossmember to LCA) is pushin ur whole LCA back. Hopefully there's no frame damage. Front crossmembers are pretty easy to find and replace. I would find a healthy CB, look at that crossmember and radius rod links and then look at yours. I hit a mega pothole that pushed my whole front right wheel back... it was the crossmember. Def. look into that

[Shag Wagon]

Hell while you are in there go ahead and upgrade to the wagon calipers and I think rotors too for that extra stopping power. Might keep you from fuckin up next time hahaha!

[XcluziveAZN]

afternoon bump for more input