More action in the Northwest Thread

[slammedEX]

haha yup good job omg it was nice here for once and i got heater working and washed my car and changed my oil and got power steering back man its a good day!

[SMseagren83]

haha yup good job omg it was nice here for once and i got heater working and washed my car and changed my oil and got power steering back man its a good day!

i washed my car too!!! then got pissed cuz i wanted to install stuff today.....but washed the car instead and ran out of daylight! FRUCKIN AYE MAN!

Sean

[maroonaccord2.2]

What's up fellas, I'm a newbie to this particular board.....but I'm down to roll in the great NW. Is this thread still going?

[d112crzy]

o yea

welcome btw. You should look at the install day/eet thread.

-Jose

[91accordwagon]

WOOOOHOOOO MY CAR IS UP AND RUNNING! Althought it's running with an a1 head now but I'ts running with the a4 header and a6 intake manifold so basically I didn't loose much power just making my powerband til 5200 instead of 5600. I haven't noticed a difference, this engine actually feels better, since my other engine had a blown head gasket I lost alot of power, this engine feels better in the torque area.

[Chan_Man]

my butt itches any meets going on?

[WarAccord]

Haha thanks for the imput Chan man. Yeah any meets? I was thinking of asking any that are nearest to Tacoma or better yet University Place wanna meet up ? Im going to be doing that DIY short throw,and Shift height possibly this weekend on a sunday, any are more then welcomed to come. I have the tools. Grinder, filer,almost all metal size drill peices,and most important , a Tap and DIE set to put some threads on.

If any wanna come on by Leave me a PM with your number, and bring your own beer~!

[Chan_Man]

What part of Tacoma? I go there like almost every other week haha.

[WarAccord]

NOT the stinky part! hehe. Im in Universty Place... so east of tacoma in the nice neck of the woods! Seriously Nice. Old people and alot of Young punks that try to show me up with there EGs all the time. like Flies on steak, never leave me alone.

Universty Place, close to Fircrest area. There are alot of nice parks here, and Im hoping that it will be nice out cause I have been lacking BBQ, and Z Beer for a great while now!. I know a park where it will be a good site to shot some pics and have some Grubb.

[slammedEX]

i'm down to drive up from vancouver for a day at the park...a sexy picnic with our cars! w00t!

[91accordwagon]

I hit up the train station for a few minutes last night, there were about 7 240's and 6 of them were ricers at best. few nice subi's though, and nice little 350 that I havent' seen in the valley before.

[WarAccord]

Hey, well this weekend seemed too short. but the best part of this short rainy weekend was that I made my own ({edit}:short throw shifter) and also Reduced the height of the shifter it self. Never liked the height of my Cb7's shifter. plus now it shifts oh so sweet!

[91accordwagon]

Nice, post some pics man.

[WarAccord]

Well I don't have a digital camera yet, but I do know how to do this now like a jiff and i know what to expect. it has it's complications that I know how to overcome. the only part difficult was lowering the shifts height. I didn't take much thought when i cut it a good 2 inchs low. I had to thread on the inside and put a bit of JB weld inside aswell. on the bracket, it was EASY! only thing was to adjust it to fit for the outher plastic casing. that I do know how to do easly since It gave me such a hard time.
I'll Charge be charging people now.
buy some beer and share!
If you don't have tools I have them.
and since im a Remodeling Forman, I can easily show you step by step and get the exact tool /s that will be needed.
so if any don't have a short throw shift PM me so I can tell ya how to get here!

[tokomo68]

Anybody up for a meet around the mill creek area sometime in the near future?