OFFICIAL NorCal Lounge Thread

[H23 Lude]

why dont you just use the IM gasket?

anywyas, this dumb bitch that i did a transmission for is ending up selling the car because the ABS light is on. if you know how to drive, you'll never need your abs. fuck abs.

anyone want to buy a 92-93 SE cb7?

eh too much work, just to install the gasket and i'm too lazy to do it.

[wed3k]

eh too much work, just to install the gasket and i'm too lazy to do it.

what about the throttle body and blacktrax spacer? just do it all, it only took danyo and i half a day to pull his manifold.

[TheNextAZN]

what about the throttle body and blacktrax spacer? just do it all, it only took danyo and i half a day to pull his manifold.

pull, cleaned, drilled and tapped the egr ports, and a mild pnp on exit ports of the manifold.. lol

dood.. about that chick with the abs light.. u should of told her about me.. lol. anyways how much is the SE selling for? dood if u still got the car.. jack the rear mud flaps! lol.

[wed3k]

pull, cleaned, drilled and tapped the egr ports, and a mild pnp on exit ports of the manifold.. lol

dood.. about that chick with the abs light.. u should of told her about me.. lol. anyways how much is the SE selling for? dood if u still got the car.. jack the rear mud flaps! lol.

nah man, i already gave the car back...i needed to get paid because i bought a bunch of shit.

180 bucks for another set of axles, ROH conversion hubs, rear disc conversion, RR window regulator and a service manual for the cb7. i can start taking apart transmissions!

but ill let you know about how much the cb7 is.

[TheNextAZN]

180 bucks for another set of axles,.

autozone specials!??!?! lifetime warranties'?

[wed3k]

autozone specials!??!?! lifetime warranties'?

i already have the lifetime warranty for non abs axles. eric knows

i just have an extra set just in case someone breaks one at the strip. i wish these were DSS stage ones.

dude, i jsut found these and it will fit my dad's lexus.
http://sfbay.craigslist.org/sfc/pts/824916853.html

his suspension is clunking on the left side anyways. he says there's a knocking on the old es300 so it maybe motor time.

[TheNextAZN]

i already have the lifetime warranty for non abs axles. eric knows

i just have an extra set just in case someone breaks one at the strip. i wish these were DSS stage ones.

dude, i jsut found these and it will fit my dad's lexus.
http://sfbay.craigslist.org/sfc/pts/824916853.html

his suspension is clunking on the left side anyways. he says there's a knocking on the old es300 so it maybe motor time.

ahahhahahah niiiceee.. time to dump the ES!

dood so my car is getting shitty in the shifting department. And from what i've read Redline MTF dosen't hold up to well after a while. I've read like 20k then change. But, heck i got like 4 more Redline MTF bottles in my garage, i figure why not? maybe add a lil SyncroMesh .. lol only thing is the drain bolt is at that shitty position.. what u think Wes take another crack at it sometime? P

[wed3k]

ahahhahahah niiiceee.. time to dump the ES!

dood so my car is getting shitty in the shifting department. And from what i've read Redline MTF dosen't hold up to well after a while. I've read like 20k then change. But, heck i got like 4 more Redline MTF bottles in my garage, i figure why not? maybe add a lil SyncroMesh .. lol only thing is the drain bolt is at that shitty position.. what u think Wes take another crack at it sometime? P

how long has it been? mines been a little harsh as well and i drive less than you do. tranny fluid flush party?

whatcha doing sunday? im doing cb7red's suspension so you shoudl come by...the shop's open.

[TheNextAZN]

how long has it been? mines been a little harsh as well and i drive less than you do. tranny fluid flush party?

whatcha doing sunday? im doing cb7red's suspension so you shoudl come by...the shop's open.

nothing planned sunday.. i'll give u a call. i'll take my damn header there too, to remove that damn broken bolt! lol.

[wed3k]

nothing planned sunday.. i'll give u a call. i'll take my damn header there too, to remove that damn broken bolt! lol.

i need to learn how to weld because one way to remove broken off studs and bolts is to find a nut and weld it onto the stud. fromt heat, you can usually take it out with the help of a wrench.

another way is oxy acetlyne torch and heat it upt ill it is red hot and put oil or wax on the stud. the expansion will allow the wax and oil fill the threads and it should come right out.

so now im debating whether or not i should put only synchromesh or try the new honda stuff.

[TheNextAZN]

synchromesh mix! i do believe i have a bottle of honda/acura MTF in my garage too

as for the bolt.. i was thinking about just drilling it out.. possible?

[wed3k]

synchromesh mix! i do believe i have a bottle of honda/acura MTF in my garage too

as for the bolt.. i was thinking about just drilling it out.. possible?

we want to preserve the threads though...but drilling is also an option.

[H23 Lude]

what about the throttle body and blacktrax spacer? just do it all, it only took danyo and i half a day to pull his manifold.

i have the blacktrax spacer already on, but im probably gonna take it out and put the plenum right on the runners creating essentially a Euro-R manifold. I still need to find a spare TB and plenum to send to max bore and another Valve cover to cut for the cam gears.

[BB6-SH]

I might have found a header, just hope the person starts to produce them soon over on HT. So that should place me in the +180whp with that type of header design if it's what im thinking it will be like. So i would upgrade to a 2.5'' cat as well. Midrange and high end shall be improved. Still would need a larger TB to complement the slightly bigger cams.

I got lucky today on the hwy 280, i was on the carpool doing 80mph. Next thing you know theres a chp on the side with his radar gun pointed directly at me. But didn't get pulled over or nothing. I'll set the cruise control at 75mph next time.

[wed3k]

I still need to find a spare TB and plenum to send to max bore and another Valve cover to cut for the cam gears.

didnt you ask me that?